Spare parts

Distancing spacer with 0,2mm hight for a centering of a brake caliper or differenc components. Can be used on many types of calipers with IS or PM mount. You can get most from the braking force if you pads contact the whole rotor surface. Spacer is made from steel and inner diameter is in size...

Copper washer or seal for HOPE brake lines. The gasket has the serial number HBSP26. The gasket is used to fit many types of HOPE brake lines. The gasket seals the connection perfectly to prevent any brake fluid leakage!

Copper washer or seal for HOPE brake lines. The gasket has the serial number HBSP161. The gasket is used to fit many types of HOPE brake lines. The gasket seals the connection perfectly to prevent any brake fluid leakage!

Olive for brake hoses Magura. Olive can be used for kevlar and also plastic Magura hoses. You will use this olive after cable shortening or new installation / replacement of master. Olive will press the hose inside the lever or caliper thanks to sleeve nut, so the hose is firmly connected to the...

Bold Magura for closing of bleed port in caliper Maguar HS11, HS22, HS33, HS33 R and Gustav M. Bold have M6 screw and head with inbus key or torx T25. Bold is made from durable steel and is possible to use it repeatedly.

Washer for MAGURA EVO2 adapter booster of hydraulic rim brakes MAGURA HS11, HS22, HS33. Washer is used below the bolt head which tighten the booster to the MAGURA EVO2 adapter (upper bolt). Sold by 1pc of washer.

Spare part o-ring for brake hose Magura MT (bajo fitting). This o-ring is compactible with Magura MT4, MT5, MT6, MT7, MT8, MT Trail Sport. O-ring is sold singly.

Washer 1mm high to support the brake or other components. It fits under different types of brakes and is used to center it. Thanks to the pads you can achieve better braking effect or the brake pads can sit on the full surface of the disc. The washer is made of steel and the diameter of the inner...

Replacement torx bolt for HOPE brakes, size M3x6mm. The bolt can be used for fixing HOPE brake lever piston stop or for other HOPE brake components. Replacement screw is sold in 1 piece.

Magura rim brake washer for Magura hydraulic rim brakes HS11, HS22, HS33 calipers. Washer is made from durable plastic and it is mounted directly on the calipers body. You can adjust the distane and angle of the calipers easily thanks to the washer. Also the washer helps to keep the calipers...

Replacement torx bolt for HOPE brakes, size M3x8mm. The bolt can be used for fixing HOPE brake lever piston stop or for other HOPE brake components. Replacement screw is sold in 1 piece.

Sleeve nut Magura for hydraulic rim brakes Magura HS11, HS22 and HS33 and also complete Magura MT series made from Carbotecture® material. Sleeve nuts keeps the hose with olive inside the lever and press the olive inside. Sleeve nut M9 is made from durable steel and it is possible to use it...

Spare part for MAGURA HS rim hydraulic brakes or MAGURA MT disc brakes. Brake lever hose cap to prevent breakage at the hose fitting. The cap slides onto the fitting and wraps tightly around it.

Sleeve nut for rim brake calipers of Magura HS11, HS22, HS33 and also RT6 and RT8. Sleeve nut nut hose tightening in the caliper. Sleeve nut will help you with tightening of olive on the hose and seal the whole braking system. Sleeve nut is made for all models of hydraulic rim brakes Magura.

Replacement o-ring 10x2mm for 14mm pistons. The ring is designed for mineral oil (made of NBR or Nitrile rubber) and brakes like MAGURA HS11-HS33

Washer 3mm high to support the brake or other components. It fits under different types of brakes and is used to center it. Thanks to the pads you can achieve better braking effect or the brake pads can sit on the full surface of the disc. The washer is made of aluminium alloy and the diameter of...

Original barbed fitting with m6 screw for Magura hose. This barbed fitting is used with all brakes which uses plastic hose like rim brakes Magura HS11, HS22, HS33, HS33 R, or MT2. Barbed fitting should be pressed in the hose with special tool or inside vise with proper adapters and hammer.

Spare original MAGURA bolt in EBT bleed port for disc brake calipers MAGURA MT (all models 2015 / 2017 / 2019 / 2-piston / 4-piston). Small bolt is made from steel and keeps the fluid inside the braking system. BE AWARE! Tightening torque of this bleed port bolt is max. 4Nm, or you can damage it!

Barbed fitting (insert) for Magura disc brakes. You can use this insert for all disc brakes from Magura MT family (excluding MT2). Easy instalation in the hose without tools or with a small tap with a hammer. Olive and shroud nut is sold separately.

Replacement rubber cap for HOPE caliper bleed screw, part number HBSP240. The cap is primarily used to keep debris out of the brake caliper hydraulic system. The cap keeps the bleed screw free of dust, mud, and other debris that could settle in its cavity. This makes it very easy to bleed the...

Spare part HOPE for brake lever HOPE Tech 3. Brake lever pivot bushing. Bushing is made from durable plastic which perfectly fit in to brake lever body. HOPE spare part number HBSP313.

Spare part of HOPE hydraulic brake fittings number HBSP159 - hose olive. Thanks to the olive, the hose will be perfectly pulled onto caliper or lever and the brake system will be sealed at the connection of the hoses to the lever or caliper.

Replacement screw for banjo hose connection to MAGURA MT brake caliper with rotatable connection. The screw is hollow with a drilled hole for the passage of mineral oil through the brake system. The screw can be tightened with a torx T25. The maximum tightening torque for the MAGURA MT banjo is 3Nm!

Covers of hose and also bots and connectors for Magura HS11, HS22 and HS33 brak calipers. Covers are made from plastic and keeps the bolts and hoses in save on critical places. Supplied as a pair (left + right) resp. for install on 1 brake. Covers are made for Magura HS11, HS22 and HS33 hydraulic...